Paul Hannell's Shed Clearance Sale - LOTS of good stuff for clubbies and others

posted May 13, 2020, 3:01 PM by Secretary - Westfield Car Club Qld   [ updated May 24, 2020, 2:21 PM ]
Paul is rationalising his business and has HEAPS of clubbie-related items for sale, plus a whole raft of other bits and pieces, performance-related and otherwise. 

New Builders Package (individual items not being offered separately, complete package only),  comprising of:-

AGE 20V Silvertop, connected to

T50 5 Speed, with 10,000 k old HD organic clutch kit, and fitted with modified for electronic speedo drive.

Remote shifter lever, linkage, and brackets,  ( this is NOT the cast housing remote I was manufacturing )

Engine has custom 1-1/2" tube, 4-1 Stainless Headers, 2-1/2" outlet, with fitting for O2 sensor,

Custom low profile, high capacity (+1 ltr) aluminium sump,  hangs 12mm below chassis.

Rubber engine mounts and brackets to suit,

S/Steel (polished) coolant tubes and radiator hoses,

Full car wiring loom, ie. chassis and engine, all fuse boxes, full instrument cluster and Ali dash panel. extra VDO temp & pressure gauges, radio,

Hella highlevel brake light in S/Steel mounting case, steering column, horn, brake light pressure switch,   etc..

All connectors & cables tagged for fitment, copy of wiring diagram and connector plug pinouts.

Approved ( Westy/Arrow Mod) ECU,

Chassis (VIN) number plate & documents & Blue Compliance Plate,

Repairable Write Off documents.

This means if you have a chassis, install my package, get a RWC Cert, have "repairable write off status" removed, 

AND GET REGO.

NO engineers  NO testing.

======================================

Complete Rear End/Diff Assy, suit De-Dion or IRS installation for +100 chassis.

Subaru R160 4.11:1 LSD,

Nissan R30 Skyline CV's both ends,

Custom machined EN26 (case hardened) Half Shafts,

Inboard vented rotors,

Mazda RX7 Turbo Calipers,

Handbrake cables to suit,

Handbrake lever,

Tailshaft flange/Yoke to suit.

Mounted on frame cut from rear section of my chassis, to allow you to copy or utilise for your installation.

 

==================================


Other Items:

1 Set      Slimline Personalised Plates, never fitted or registered,  7 FOR 2

1 Pr        GAZ 13" ( Front) Shockers, done 10,000 K's   

1 Pr        300 lb springs to suit above

----------------------------------------------

1              Build Table, Fabricated 75x50 Steel Tube, fitted with 4 x 80mm swivel - braked castors, 25mm painted plywood top, removable, 20mm plywood storage shelf below.

1              New SPA ( England) 12.5" flat bottom steering wheel.  Un drilled, no horn button.

1              Stainless Steel Roll Bar Tube, this is just a mandrel bent tube to suit +100mm chassis.

4              TC/TD Hat Style Rotors, New Old Stock

6              TC/TD/TE/TF front hubs only, suit hat style rotor

3              TC/TD early front hubs, suit flat (english) style rotor

10-ish      50mm steering rack extensions M14, suit Escort & +100 chassis, or shortened rack for Wide Westy/Book Chassis

3              4AGE   Light (5.2kg) Billet 4140 Chrome Moly Flywheels.  These are what John Bosci was selling.  Ring Gear fitment assistance avail.

2              4AGE Super light (3.8kg) Billet Chrome Moly Flywheel. Ring Gear as above

1              4AGE Light (5kg) one Piece flywheel/ring gear   

2 sets    4AGE Stock Headers

4 sets    Header Flanges, Laser Cut 10mm plate,  to suit 4AGE

4              Starter motor suit 4AGE/7AFE. Some are stock bolt pattern, a couple have been modified to suit T50 bellhousing.

                                I can do mods to shorten bolt pattern if needed.

1              Fabricated Ali Sump, low profile, similar to ProSump on my engine, but only a bit over stock capacity and MUCH easier to install

1              AE110 ( I think ) instrument cluster

1              100kW 4AGE ECU

2              Wiper motor units, ex BMC I guess,  maybe mini, morris, austin, Leyland..  Not sure look like Lucas manufacture. Pics avail

===================================


This list will be updated as items are sold so that what is listed is what is actually currently available. 

 

If anyone is interested in the above or the upcoming stuff, can they please email on the address below, I will forward a list, and make contact them from there.

 

All enquiries to Paul via shedclearance@hotmail.com

 

Comments